ALTERNATIVE ENERGY FORUM - etc.
Welcome,
Guest
. Please
login
or
register
.
1 Hour
1 Day
1 Week
1 Month
Forever
Login with username, password and session length
This topic
This board
Entire forum
Home
Search
Login
Register
"I have not failed. I've just found 10,000 ways that won't work." -
»
Misc.
»
PRUSA 3D Printer
« previous
next »
Print
Pages:
1
[
2
]
Author
Topic: PRUSA 3D Printer (Read 108 times)
0 Members and 1 Guest are viewing this topic.
Caleb
Hero Member
Posts: 1977
Re: PRUSA 3D Printer
«
Reply #15
on:
March 19, 2021, 05:32:51 pm »
Halfway there; six hours to go.
«
Last Edit: March 21, 2021, 10:54:25 am by Caleb
»
Logged
CG
Administrator
Hero Member
Posts: 4249
Re: PRUSA 3D Printer
«
Reply #16
on:
March 19, 2021, 05:41:15 pm »
Very 😎 cool.
Does the printer or the stl file supply all the support structure thats supporting the bottom of the blades on the table? Is it automatically figured out and put in? Or is it just a consequence ?
Logged
Caleb
Hero Member
Posts: 1977
Re: PRUSA 3D Printer
«
Reply #17
on:
March 19, 2021, 05:52:12 pm »
The "slicer" program (free from a number of sources) puts the support in automatically as well as fills in the insides.
Logged
CG
Administrator
Hero Member
Posts: 4249
Re: PRUSA 3D Printer
«
Reply #18
on:
March 19, 2021, 07:34:23 pm »
I just noticed that the vawt arms have the same airfoil profile as the blades. I guess there will be no axial thrust force on the bearings, it may even take off.
Logged
Caleb
Hero Member
Posts: 1977
Re: PRUSA 3D Printer
«
Reply #19
on:
March 19, 2021, 07:41:01 pm »
The upper arms will be upside down. They will push back. ;-)
That funny wiggle in the transition is visible in the printed part. I'll have to fix that in the final version if it works.
Logged
Caleb
Hero Member
Posts: 1977
Re: PRUSA 3D Printer
«
Reply #20
on:
March 20, 2021, 07:19:42 am »
The bottom finished at around 11:00 pm. I started the top this morning and it should be done around dinner time.
The printed parts are a bit heavy. I could see them having balance issues. And splitting the part in the middle of the vertical surface makes it weaker in a highly stressed area so strength may be an issue too.
«
Last Edit: March 21, 2021, 10:55:16 am by Caleb
»
Logged
Caleb
Hero Member
Posts: 1977
Re: PRUSA 3D Printer
«
Reply #21
on:
March 20, 2021, 07:45:33 pm »
The top half is printed. I made a few dowels and put the two halves together; they are not glued yet. The center pillar is just a smidge longer than the sides. I don't know why.
I have the steel shaft. Bearings and magnets are due to arrive on Friday. I have to design and print the base and a cap for the top.
«
Last Edit: March 21, 2021, 10:55:45 am by Caleb
»
Logged
CG
Administrator
Hero Member
Posts: 4249
Re: PRUSA 3D Printer
«
Reply #22
on:
March 20, 2021, 07:48:17 pm »
Nice. I think it will work.
Logged
CG
Administrator
Hero Member
Posts: 4249
Re: PRUSA 3D Printer
«
Reply #23
on:
March 21, 2021, 08:30:18 am »
Time to start a wind turbine topic.
Logged
Caleb
Hero Member
Posts: 1977
Re: PRUSA 3D Printer
«
Reply #24
on:
March 21, 2021, 10:46:32 am »
I was thinking that too. I'll try moving some of these photos etc. to a wind turbine topic.
Logged
Print
Pages:
1
[
2
]
« previous
next »
"I have not failed. I've just found 10,000 ways that won't work." -
»
Misc.
»
PRUSA 3D Printer